1974 Datsun 260z with LS3 V8 (similar 240z 280z)

Price: US $12,500.00 Item location: Chicago, Illinois, United States

Description:

1974 Datsun Z-Series

Up for sale is my hybrid 1974 Datsun 260z with a built LS3 (for those that are unfamiliar, the LS3 is a 6.2L V8 which is found in late model Corvettes and Camaros) hence its project name of 620z.I have been building it to keep, but unfortunately after moving to downtown Chicago a couple of years ago, I have found that I don't have enough extra time or space to work on it anymore.As you can tell from the pictures, most of the effort thus far into the project has been in building the powertrain to be rock solid and reliable. The engine makes over 500 hp and has the components to back that up all day.

The good (beyond the build sheet listed below):

-Custom built engine mounts use the superior late model GM LS engine isolators and places the engine much lower and farther back in the bay than the conversion kits that you can buy. This position created under 52% front weight bias. (Total vehicle weight 2538 lbs.)

-Very low mileage since build (estimated 1500 miles).

-Originally a southern car (bought in Arkansas, built in Tennessee, garage stored since trailering to Chicago and driving less than 50 miles in IL and only during the summer.)

- Built without shortcuts and with the intention of keeping it forever, but unfortunately, life gets in the way of good plans.

-Title in hand.

The bad:

-The floor pans were rusted out so I custom fabricated replacements.Concerned about structural integrity, I built a subframe in this area which also serves as better structural mounts for the seats and carries the additional weight of the transmission.

-The custom exhaust system was made in a rush at a local exhaust shop. It currently rides low enough that it will scrape the pavement if driven over a sizeable bump. I planned to reroute.

- The outside door handles are currently not installed (I think I have one of them), so I use the inside door handles to enter.

-See pictures of all vehicle rust.I have not left any out.A few areas have rusted through, but most of the rust on the bodywork seems pretty much cosmetic.These panels still feel solid.

-Headlights did work but are not working currently (I think it is the switch on the column).When they did work they were pretty dim and could stand to be rewired.Brake lights work but turn signals do not.

-Gets worse fuel mileage than I would expect.May need to adjust some settings in the self-tuning ECU.

-Gauges aren't currently connected but the ECU and TCU diplays give all vital info (oil pressure, engine temp, voltage, RPM, speed, and lots more).I also wired an alternator fault and high engine temperature warning light in the custom fabricated center panel.

More Pictures available.

Engine - LS3

Block - Aluminum 6.2L

Heads - Stock GM LS3 (new for build)

Crank - Stock GM LS3 (balanced by Lunati Cranks)

Rods - Stock GM LS3

Rod Bolts - ARP

Pistons - Stock GM LS3

Piston Rings - Total Seal

Oil Pan - Corvette "Batwingâ€

Oil Pump - Melling High Volume

Camshaft - Comp Cams Street/Strip Grind

Timing Set - Comp Cams Gear Drive

Lifters - Comp Cams Short Travel Hydraulic

Pushrods - Comp Cams 3/8" Magnum Single Piece

Rocker Arms - Comp Cams Ultra Gold Aluminum 1.72 bolt down

Springs - Comp Cams Dual Spring

Retainers - Comp Tool Steel

Valves - Stock LS3 (hollow stem intake)

Intake - Fast LSxr

Throttle Body - Fast 102mm

Fuel Rails - Fast Extruded aluminum

Fuel Injectors - Fast Precision Matched 39 lb/hr

Pressure Regulator - Fast Billet Aluminum Fully Adjustable

Front Cover - Comp Cams Cast Aluminum

Harmonic Balancer - TCI Rattler

Water Pump - Stock GM LS3 (new for build)

Alternator - Stock GM

Exhaust Manifold - Hooker Ceramic Painted

ECU - FAST EZ-EFI Self-Tuning System with touch screen programmer integrated into dash

Starter - TCI Permanent Magnet

Battery - Optima Red Top

Power Distribution - Master Cut Off Switch through Late Model Ford Fuse Block

Drivetrain

Transmission - TCI 4x 4L60e Performance Built

Torque Converter - TCI Custom Built, Billet Front

Flexplate - TCI Billet, SFI Approved

TCU - TCI EZ-TCU programmable, self tuning with controller integrated into dash

Shifter - TCI Outlaw with push button shifters

Differential and halfshafts - R200 from a 280z

Suspension and Braking

Springs - Eibach 1" lowering

Shocks - Tokico

Bushings - Energy suspension, full kit

Front Brake Calipers - Toyota 4-piston upgrade

Front Brake Rotors - Vented upgrade (new for build)

Rear Brakes - Drums turned and rebuilt

Master Cylinder - Power brake upgrade (new for build)

Other

Wheels - Western Wheels Cyclones 14 x 5.5

Tires - BF Goodrich (new for build and not abused)

Head Lights - KC (new for build)

Windows and Locks - Spal electric conversion kits included but not installed

Seats - 350z mesh

Fuel Tank - Plastic Camaro with Inlet in Stock Location

Fuel Pump - Fast (Walbro) In-Tank 1200hp

Fuel Plumbing - Fast black braided line with black AN fittings

Radiator - Aluminum (new for build)

Seat Belts - Racequip 4-point Harnesses (5thpoint included but not installed)

Vehicle Details:

Condition: Used
Make: Datsun
Model: Z-Series
SubModel: 260z
Year: 1974
Mileage: 1
VIN: RLS30
Engine size: 6.2L LS3 V8
Number of cylinders: 8
Transmission: Automatic
Vehicle Title: Clear

Want to buy? Contact seller!