1968 Ford Mustang Hatchback Red RWD Manual Fastback with Chassis Works Chassis
1968 Ford Mustang Fastback with Chassis Works Chassis
Vehicle Details1968 Mustang Fastback that originally was a 289 with a 3 speed manual transmission. The car is sitting on a complete Chassis Works by Chris Alston Chassis. All information on the chassis is included in the pictures. The rear end is a customized independent 9in Rear End. We decided to go a different direction with a project which is why this is up for sale. The original engine and transmission are not included.
Chassis Information
g-Street Rocker IRS Chassis 64-70 Mustang Contains: Welded A-Arm
& Rocker IRS Frame, Engine and Transmission Chassis Mounts, Inner
Rocker Panels, Seat Platform Tunnel Transition, Front Firewall,
Complete Floor Behind Firewall with Transmission & Driveshaft
Tunnels, Wheel Tubs & Package Tray Bulkhead, Accepts g-Machine or
Pro-Billet Upright Front Suspension, Coil-Over Rocker-Arm IRS with
Splined Antiroll Bar Rear Suspension. Front Frame Outside Width 32"
With Rear Frame Outside Width 35", Optional Roll Bar or Cage.
PALLET 2 WAY68 x 36 HEAT TREATED WOOD, FORK ENTRY ON
36" SIDE ONLY FOR WELDED CLIPS
Build Specs:
36 x 68 Two Way Pallet
3-36 inch long 4 x 4 Stringers
6-68 inch 2 x 4 Decking
Starting from one 68 inch Side. The First 2 x 4 Board is Flush with the
Side, 1" Gap then Second Board, 1" Gap then Third Board, Evenly
Space the Other 3 Boards from there to Evenly Fill up the Remainder of
the 36 length.
MAINHOOP 65-70 FASTBACK MUSTANG DOM 1-3/4 x .125 TILTED
BACK STYLE FOR EXACTFIT CAGE
4872-04-2 EA 1.0000 0.0000 0.0000 COMPONENT
WINDSHIELD BRACE 65-70 MUSTANG DOM 1-3/4 x .125 TILTED
BACK STYLE FOR EXACTFIT CAGE FITS COUPE & FASTBACK
CAGE SIDE DR 65-70 MUSTANG DOM 1-3/4 x .125 THROUGH DASH
FOR EXACTFIT CAGE FITS COUPE & FASTBACK
CAGE SIDE PS 65-70 MUSTANG DOM 1-3/4 x .125 THROUGH DASH
FOR EXACTFIT CAGE FITS COUPE & FASTBACK
Rear Strut Fastback OEM/g-Street Frame DR 65-70 MUSTANG DOM
1-3/4 x .125 Driver Side Follows Roof Thru Package Tray Attaches to
Outrigger on Rear Frame Behind Wheel Tub or Floor in OEM Frame for
Exact Fit Roll Bar & Cage
Rear Strut Fastback OEM/g-Street Frame PS 65-70 MUSTANG DOM
1-3/4 x .125 Passenger Side Follows Roof Thru Package Tray Attaches
to Outrigger on Rear Frame Behind Wheel Tub or Floor in OEM Frame
for Exact Fit Roll Bar & Cage
SIDE BAR DOM 1-3/4 ROLL CAGE 65-70 MUSTANG M/S 1-3/4 x .125
1-BEND FOR EXACTFIT ROLL CAGE FITS BOTH SIDES
Builder Tubs 34 Dia x 21Widex 18 Gauge Steel with 3-1/4" Extra Skin
Length Per Side Past End Cap. Shipped Unassembled for Easier
Installation.
TREMEC T-56 Magnum 6 Speed Mount With Driveshaft Loop & Torque
Arm Mount for 7740-7742-7743 64-70 Mustang g-Street Chassis
FITMENT NOTE:
Fits Aftermarket T-56 MAGNUM Transmissions TUET11009 &
TUET11012 and Others with Crossmember Mount Bolts 26.6 Inches
Behind Back of Engine. Tailshaft Mount Pad is 4.930 Below Centerline.
SWINGOUT CLEVIS & SINGLE EYEBOLT 1-3/4x.134 ROLL CAGES
7044 EACH 1.0000 0.0000 0.0000 COMPONENT
Back Brace gStreet 1-3/4 TubeBolt-In Connection
Hardware 774X-M10 g-Street Chassis 7740-M10, 7741-M10, 7742-M10
& 7743-M10
7950-7740M10F EACH 1.0000 0.0000 0.0000 COMPONENT
Front Floor 4Link/TA/IRS 65-70 Mustang 774X-M10 g-Street Chassis
With 4-Link, Torque-Arm or IRS Rear Suspension. Contains Front Inner
Splash Pans, Complete Floor Behind Firewall Foward of Main Hoop 2x4
Crossmember. With Front Floor, Transmission Tunnel, Seat Platform,
Tunnel Transition, Drive Shaft Cover and Driveshaft Floor.
Rear Floor IRS 64-70 Mustang 7722/7723/7742/7743-M10 g-Street Clip
& Chassis With IRS Rear Suspension. Contains Complete Floor Behind
2x4 Main Hoop Crossmember With Package Tray Bulkhead.
Install Guide 7055-M10 65-70 MUSTANG ExactFit Roll Cage 1-3/4
DOM
Install Guide 7740 Thru 7743-M10 g-Street Full Frame Chassis & Floor
With 4Link, Torque Arm & IRS Rear Suspension For64-70 Mustang
GUSSET A-PILLAR CAGE SIDE gSTREET CHASSIS F-10 & F20 &
M10
Rear IRS Rocker Clip Low g-Street Ground Clearance M10 Chasssis
Low Ride Height 35" Wide 4 x 2 Clip 64-70 Mustang GEN2
Rocker Wireway Assembly DR g-Street Chassis M10
Rocker Wireway Assembly PS g-Street Chassis M10
Front Clip V8 Ford g-Street 64-70 Mustang Includes SB/BB Ford Engine
Frame Horns & Center 2x4 Frame Rails With Splined ARB Mounts
Measuring Tab Front Bumper Mount M10 Clip g-Street Chassis
TUBE 1-1/4 x .120 DOM x 60.000 INCHES LONG +or- .050 YIELD IS 4
PIECES PER 20 FOOT LENGTH
TUBE 1-3/4 x .125 DOM x 60.000 INCHES LONG +or- .050 YIELD IS 4
PIECES PER 20 FOOT LENGTH
Clip Steel Mount Adjustable 351 Small Block Ford, Use With TCP Front
Clips Only. Welded Steel Construction. Adjusts Front to Rear in
Chassis. See Data Sheet For Oil Pan Fitment Info. Not For Use With
260-289-302 Engines
gStreet Chassis Billet Upright A-Arm Front Suspension Includes Billet
Aluminum Front Uprights, Wide-Trac Billet Upright Upper and Lower
Control Arms, Power Rack and Pinion with Bumpsteer Adjustable
Tierods, Splined Antiroll Bar, Varishock Coi-lOvers with Springs.
Bill Option 1 Option Code: 31 Tubular Control Arms Aluminum Wide-Track Upright
Bill Option 2 Option Code: 01 4-1/2 Bolt Circle Spindle In Front Aluminum Upright
Bill Option 3 Option Code: 57 POWER RACK BLACK 32" CSMBR 23.5" RACK CENTER
Bill Option 4 Option Code: 32 32" Frame Width Splined Arm Billet Mount Antiroll Bar
Bill Option 5 Option Code: 61 Pivot-Ball Q4 4-Way & Bolts Remote Reaservior
Bill Option 6 Option Code: 12 HEAVY SB ALL ENGINE MATERIALS CHEVY ENGINE 550 lb
Bill Option 7 Option Code: 02 14" - RED 6 PISTON CALIPER DRILLED & SLOTTED BLACK ROTOR
COILOVER BOLT SET, GRADE8, FOR A PAIR OF SHOCKS
Hardware 1/2-Stud Upright II/IRS 14" W4A/W6A Aero6 Caliper Includes
Hats, Caliper Brackets and Hardware for 14 x 1-1/4 Rotors with W4A or
W6A Aero6 Wilwood Calipers
Threaded 3/4 Bumpsteer 9/16 -18-Right Adjuster Sleeve Rack
Connection with 5/8 Left Hand Alloy Steel Rod End Tierod Use With
Street Machine Power Racks.
UPRIGHT FRONT ONE-PIECE S/M FRONT 4-1/2 Bolt Circle
CHASSISWORKS CLIPS, ALUMINUM BODY WITH UNIT-BEARING
SPINDLE INCLUDES STEERING ARM WITH 3/4 THREADED BORE
FOR 5/8 RODEND STYLE TIEROD END
FITMENT NOTE: MINIMUM RIM SIZE 18" DIAMETER DEPENDING
ON WIDTH.
Rack Mount SM 32" CrossmemberWith 6140-32-M40 Rack
Power Rack 32" Clip 3/4-36 Input Spline With 9/16-18 Tierods & 43-3/4
Tire Rod Length Left Hand Front Steer, For Street Machine Suspension
On 32" Outside Width Frame (65-70 Mustang) Use With Rack Mount
Set 6139-32-M40
A-ARMS UPPER WIDE-TRAC for BILLET ALUMINUM UPRIGHT ON
g-STREET MACHINE CROSSMEMBER
A-ARMS LOWER WIDE-TRAC for BILLET ALUMINUM UPRIGHT ON
g-STREET MACHINE CROSSMEMBER
SHOCK SIMULATOR FOR 12.0" RIDE HEIGHT
HARDWARE BOX 5735 SPLINED FRONT ANTIROLL BAR FOR ALL
G-MACHINE CLIPS
5735 - 32" CLIP SPLINED ARB FRONT ANTIROLL BAR G-MACHINE CLIPS WITH 32" OUTSIDE WIDTH
INSTALLATION GUIDE S/M A-ARMS
CO Q4 Remote Reservior Quad-Adjustable STD Pivot-129 Pivot-129
4.25 Travel, 14.31" Extended Length, Top Is Standard Pivot Ball with
1/2 Bore x 1.290 Long Sleeve, Base Is Standard Pivot Ball With 1/2
Bore x 1.290 Long Sleeve, KCR Valving
VARISPRINGS 9" LONG x 550 LB/RATE, SILVER POWDER COATED,
BOXED PAIR
W6A-RH AERO6 RED CALIPER 1-1/4 x 14/15" ROTORS, 6 PISTON
1.62/1.12/1.12, 7.090" RADIAL MOUNT, PASSENGER SIDE BEHIND
AXLE MOUNT, uses 6617 type Pads
W6A-LH AERO6 RED CALIPER 1-1/4 x 14/15" ROTORS, 6 PISTON
1.62/1.12/1.12, 7.090" RADIAL MOUNT, DRIVER SIDE BEHIND AXLE
MOUNT, uses 6617 type Pads
Pad W6/W4 Street & Performance BP-20 Smart Pad Causes Light
Dusting Polymatrix Type 6617 4 Pack
ROTOR SRP 1.25 x 14.00" PASSENGER
ROTOR SRP 1.25 x 14.00" DRIVER
Suspension Rocker-Arm IRS gStreet Clip & Chassis Includes UCA,
LCA, Toe-Links, Pushrod Rocker Arm System, FAB9 Center with Billet
Aluminum Rear Uprights, Stub Shafts with Halfshafts, Varishock
Coil-Overs with Springs. No Dropout Thirdmember Included. Optional:
Driveshaft Loop Pinion Support, Wheel Stud Pattern or Centerlock
Spindles, Shock Valving, Spring Rate, Splined Antiroll Bar & Brakes
Bill Option 1 Option Code: 54 Half Shafts for 54" Hub Width 64-70 Mustang
Bill Option 2 Option Code: 45 4-1/2 Bolt Circle Wheel Studs 1/2-20 Thread
Bill Option 3 Option Code: 02 Strange Pro-Aluminum Ford 9 Dropout Pinion Mount Included
Bill Option 4 Option Code: 04 COM-8 Q4 4-Way & Bolts Piggy-Back Remote Reaservior
Bill Option 5 Option Code: 50 Baseline Spring Rate 500 lb.
Bill Option 6 Option Code: 14 14 SRP 1/2-Studs Black Wilwood Caliper & E-Brake Mechanism
Bill Option 7 Option Code: 54 Splined Arm Antiroll Bar 54" Rear Hub Width
Bill Option 8 Option Code: ST Strange S-Trac Helical Gear 35 Spline Differential
Hardware 1/2-Stud Upright II/IRS 14" W4A/W6A Aero6 Caliper Includes
Hats, Caliper Brackets and Hardware for 14 x 1-1/4 Rotors with W4A or
W6A Aero6 Wilwood Calipers
Hardware E-Brake Unit Hub-A IRS Parking Brake Assembly for use with
8383-14 thru 8384-15 Brake Kits
IRS Tubular LCA Pivot-Ball Bearing Rodends Matte Black
IRS Toe-Links 5/8 Rodends with Bumpsteer Adjuster
IRS Tubular UCA Pivot-Ball Bearing Rodends Matte Black
Upright IRS 4-1/2 Bolt CircleAluminum Body With Unit-Hub Bearing
Spindle and Series 21Stub Shaft. Integal Toe-Link Arm With 3/4
Threaded Bore For 5/8 Rodend Style Toe-link End. Spindle Cap Has
2.780 Wheel Register Diameter.
FITMENT NOTE
Minimum Rim Size 18" Diameter Depending on Rim Width.
Shock IRS Rocker Assembly 1/2Rodends x 13.40 Long Link Rods For
IRS Pushrod Shocks
Pinion Support D/S Loop 9" Ford Strange HD Pro Aluminum Dropout
For IRS Includes Driveshaft Loop
ARB Splined Bar 7/8-48 x 0.88Solid Straight Arm Hardware Box For
5861-S-088-XXXX
Solid ARB 0.88 x 28.00 x 7/8-48 Spline Flat End for 5/8 Thick Arm for
54 Hub Width Rear IRS
FAB9 Assembly for IRS With 35Spline Stub Axles
Assembly Half Shaft CV Joints& Boots 35 Spline 45° PA 13.625 Overall
Length
Assembly Half Shaft CV Joints& Boots 35 Spline 45° PA 15.625 Overall
Length
INSTRUCTIONS & DRAWING FOR 8383-14 with UNIT HUB-AB
C/O PR LEFT Q4 COM8-1 4.25 TRAVEL QUAD ADJUSTABLE
PIGGYBACK RESERVIOR WITH COMPRESSION KNOBS ON LEFT
SIDE OF REBOUND KNOBS, COILOVER FOR 2-1/2 ID SPRINGS,
10.06 to 14.31 LENGTH, 1/2 BORE x 1" WIDE COM-8 BEARINGS IN
BOTH EYES, ROAD RACE RR VALVING, SHOCK ASSEMBLY WITH
3/4 EXTENDED UPPER COIL SPRING SEATS AND LOWER SPRING
SEAT
- SPECIAL ORDER PART NOT RETURNABLE FOR ANY REASONVAS
C/O PR RIGHT Q4 COM8-1 4.25 TRAVEL QUAD ADJUSTABLE
PIGGYBACK RESERVIOR WITH COMPRESSION KNOBS ON RIGHT
SIDE OF REBOUND KNOBS, COILOVER FOR 2-1/2 ID SPRINGS,
10.06 to 14.31 LENGTH, 1/2 BORE x 1" WIDE COM-8 BEARINGS IN
BOTH EYES, ROAD RACE RR VALVING, SHOCK ASSEMBLY WITH
3/4 EXTENDED UPPER COIL SPRING SEATS AND LOWER SPRING
SEAT
VARISPRINGS 8" LONG x 500 LB/RATE, SILVER POWDER COATED,
BOXED PAIR
VAS 523-100 SET 1.0000 0.0000 0.0000 COMPONENT
Anti-Rotation Shim COM-8 Shock Base 1.45 OD x .61 ID x .19 Long
Delrin, Set of 4 Pieces
W4A AERO4 Red CALIPER 1-1/4 x14/15" ROTORS, 4 PISTON
1.12/1.12, 7.090" RADIAL MOUNT, FITS BOTH SIDES, uses 6617 type
Pads
Pad W6/W4 Street & Performance BP-20 Smart Pad Causes Light
Dusting Polymatrix Type 6617 4 Pack
ROTOR SRP 1.25 x 14.00" PASSENGER
ROTOR SRP 1.25 x 14.00" DRIVER
Using a Strange S-Trac 35 Spline 9" Ford Differential. Not Inccluded, Requires Optional Purchase.
Fuel Tank -10 Supply M10 gStreet Rear Clip & Chassis 65-70 Mustang
Approximately 17 Gallon Capacity. Tank Only, Can Be Trunk or Remote
Filled. Requires Chassis Mounts, Fill Kit and Vent.
Fuel Tank Remote Fill Universal90° Hose For Rear Clip & Chassis.
Includes Aircraft Cap, Filler Tube with Hose and Recessed Ring to
Attach Cap To Rear TailLight Panel
5908-VC1 EACH 2.0000 0.0000 0.0000 149.0000 298.00
Vent Canister Billet AluminumBlack Anodized-6 Inlet With 40 Micron
Sintered Vent. Use for Fuel Tank, Axle Housing & Transmissions.
Require Mounting Bracket and Connecting Hose.
Vent Remote Breather With Premium Hose Contains-6 x 36" Black
Push-Lite Race Hose, One of Each Hose End, Straight, 45° and 90°, 40
Micron Sintered Vent, -6 Male x Female -8 ORB Bulkhead Fitting With
Jam Nut and Bolt-On Chassis Mounting Bracket. Use for Venting Fuel
Tank, Axle Housing & Transmissions.
Vent Can Premium Hose Only Contains -6 x 36" Black Push-Lite Race
Hose, 2 Hose Clamps and One of Each Hose End, Straight, 45° and
90°. Use to Attach Vent Can to Axle or Gas Tank.
RESERVOIR CLAMP x 1-5/8 TUBE PARALLEL AXIS STYLE
CONTAINS A PAIR OF MOUNTS TO ATTACH TWO2.225 od
RESERVOIR to 1-5/8 TUBE
DUAL SILO ANGLED 41° g-STREETSURFACE RESERVOIR MOUNT -
Contains single mount for two VariShock remote reservoirs. For use
with 7740-M10-R rear floor tin kit or 41-degree angled panel.
FORD-9 4.11 35 S-Trac HD Pro Aluminum DROPOUT Contains HD Pro D/S PART
Aluminum Housing, Oil Channel Pinion Support, 4.11ratio 8620
Gearset, 35 Spline Strange S-Trac Helical Gear Differential
Chromemoly 1350 Yoke
Differential Yoke U-Bolts 1350 Series U-Joint Yokes On Ford 9"
Dropout - Pair
- Make: Ford
- Model: Mustang
- Type: Hatchback
- Trim: Fastback with Chassis Works Chassis
- Year: 1968
- Mileage: 10000
- VIN: 8F02C152899
- Color: Red
- Engine size: 289
- Number of cylinders: 8
- Fuel: Gasoline
- Transmission: Manual
- Drive type: RWD
- Vehicle Title: Clean Want to buy? Contact seller!
