1957 chevrolet 150 post gasser project with a built 454

1957 Chevrolet Bel Air/150/210 150 gasser

listing this for a friend, lease ask if you have any questions.
1957 chevrolet model 150 2 door sedan gasser project with a clean title.
the engine is a 454 with 4bolt mains. just about everything is new in it. it was built by a professional engine builder and has not been fired in the car.it has rectangle port heads #6272990 which have comp roller rockers and push rod guides. block is 30 over with flat top pistons,steel crank,weiand aluminum water pump,aluminum crank and water pump pullies,aluminum valve covers,crome alternator and bracket,milodon oil pan,timing cover,flywheel,all new bolts and balancer. there is alot of money just in the engine.there is a offenhauser 5904 tunnel ram, used holley carbs,and 2 k+n air filters sitting on top of the engine. the headers are also new. new afco aluminum radiator with an electric fan. trans i'm told is a b+m built turbo 400 which is used but came out of a working car. there is a new 3250 stall convertor included. the rear end is a narrowed 12 bolt chev and gears appear to be 3:73. it came from the same car as the trans did. the front axle is a speedway full width 916-3903 and king pin 910-32123. also has a new front disc brake kit which has new rotors,calipers,pads,pins/slides,seals,bearings,crome master cylinder. front rims are new et with new bfgs p155/80r15 tires. rears are used weld(need polishing)rims with junk mickey thompson 29x18.5-15 lt tires.there is alot of used parts included like: b+m shifter,ladderal bars,2 steering columns(1 with tilt),4 window regulators,doors latches,150 side trim,tail lights,head light trim,stock 57 gauges cluster, lutch pedal, ear window, 50 hood without the bullets, oor vent window frames,and other parts pictured.
the body needs work. the floors have been fully cut out. there is a new 2 peice full floor included. also 2 new outer rockers and 2 new rear quarter panels are included. these were all purchesed from dan chuk parts. the front fenders,doors,trunk lid,hood, indow channels are in good shape and usable. the front stub/straight axle was started and welded in place but will need to be finished. the engine and trans mounts are welded in place as well and the engine and trans are mounting in.
the car is not complete and is for sure missing: windsheild, utside windshield trim,side glass,seats,drive shaft(yoke is in the trans), teering linkage from the steering box to the wheel,bumpers,grille and more. the parts pictured are what goes with it.
this is a mean looking car as it sits i can only imagine what it would look like done pulling into a car show or a cruise nite finished!
prior to the reserve being meet the car is for sale as a roller with or without the parts or also with a more stock good used 454 with oval port heads and an edelbrok aluminum intake in place of the built 454 in the car now. will also entertain trades of muscle cars and muscle car projects but if the reserve is meet then these options are all gone!
i have more pictures i can send and if you have any questions please ask. email or call 9206603810

On Nov-03-15 at 10:04:56 PST, eller added the following information:

all of the parts fit in the car for shipping.

• Condition: Used
• Make: Chevrolet
• Model: Bel Air/150/210
• SubModel: 150 gasser
• Type: Sedan
• Trim: 150
• Year: 1957
• Mileage: na
• VIN: va57s222...
• Engine size: 454
• Number of cylinders: 8
• Fuel: Gasoline
• Transmission: Automatic
• Drive type: RWD
• Vehicle Title: Clear
Want to buy? Contact seller!