1974 BMW 2002 Rally Car Pike Peak Hill Climb Race Car
1974 BMW 2002
1974 BMW 2002 -
Car was built in 2009-2010, and on the Mountain for it's first race in 2010.
CAGE AND SUB FLOOR -
PPIHC approved Safety Cage and Floor, 1.75x.095, 1020 seamless tube, 1/16" cold Rolld Plate Floor (except Tunnel)
The cage was built by Metalhaus and Jessi Combs to SCCA GCR for a max weight car, and the PPIHC bought off on that construction.
The floors were replaced (except the tunnel) by Metalhaus with 1/16" cold roll plate and additional formed cross members were added. The floor is painted flat black, so it's a little hard to see the replacement pieces in the pictures. The rear damper towers are solid, and are reinforced with cross bracing and tied into the cage. This is per the rules for PPIHC. I know its kind of hard to see in the pictures, but the trunk picture shows where they poke through into the passenger compartment.
(By the way, Metalhaus was the company of Jake Wreesman & Jessi Combs. Jake is very well known in the Desert Racing Circuit in Southern CA, and is an amazing fabricator, crew chief and driver. Jessi has several TV shows, Rock Crawling and offroad racing fame - both are WyoTech grads, great friends, and top notch fabricators.)
Engine Components - Ireland Engineering
Engine Balance and Build - Ron Williams
Head Porting and Shaving- fine tuned by Ron Williams (German 518 turbo head with massive valves, ports, valve springs, titanium keepers, and been shaved about 2mm. With the pistons, we were just over 11:1)
Springs and Keepers - Ireland Engineering
Re-cut camshaft - Ireland Engineering
Peened Rods
Forged and relieved pistons
Compression ratio over 11:1 - 105+ Octane fuel ONLY - we ran 110 on The Mountain
High pressure and volume pump - Ireland Engineering
Oil pan sump modification - Ireland Engineering
The car has a custom long runner intake made from a 320i, port matched and modified for a Holley 2-barrell. The carb will make up to 220hp. Carb was modified and set for PPIHC altitude and competition (Mark Sullens was kind enough to help us out on the mountain with tuning during his downtime and when he wasn't needed to support his E-85 cars. He removed the power-valve and helped dial everything in. He's a great guy and true race enthusiast, and he knows his carbs! His website Mark Sullen's E85 Carburetor Conversions ) Our thoughts on a long runner manifold were to hopefully broaden the power band for hill climbing, while allowing the engine to breathe well enough to make power to 8,000+ rpm.
The transmission is not the stock trans. It is a Getrag 245 5-speed, from a 320i. It was opened up for inspection before the 2011 race and all gears/synchros were in excellent condition. It has not been looked at since, but I would be expect it to be the same. One recommendation for running PPIHC again would be to increase 3rd gear ratio, reducing gap between 2nd and 3rd, that seemed to be where we were losing a little time consistently.
Solid engine, trans and suspension mounts - Ireland Engineering
Flat plate clutch - Ireland Engineering
Brake rotors, calipers and pads - Ireland Engineering
Springs - Eibach
Damper - Bilstein
LSD differential with 4:1 gearing
Wilwood pedals, masters, and reservoirs
Throttle pedal has welded toe grab
Custom aluminum center dash
Fire suppression system including engine bay and trunk compartment nozzles
Autobaughn Wheels
Tires have under 100 miles on them and several races left. They were run on 3 tuning days on the mountain, and then one more time up on race day.
5 point harnesses for Driver and passenger
Aluminum Fuel cel with RCI Foam
Baker Race Battery
Momo Seats
There is also another custom, long runner manifold that was used with a speed-density Holley Commander 950EFISystem. This system was used with an Accel ignition and made tons of power in California. We had issues with re-mapping for the 2010 race at 12,000+ altitude, so we took all theEFIstuff off and returned back to a Bosch distributor and carbureted system. The additional custom manifold will go with the car, but the Holley system is long gone and does not come with the car.
We never Dyno'd the car, but on paper with the head porting/shaving, cam, and an approximate compression ratio of 11-11.5:1 - you should be between 205 - 220HPat 8000-8500 RPM
This car took SECOND PLACE at the 2011 Pike's Peak race in the Rocky Mountain Vintage Class under 4 liters (we were awarded 1st place, but later surrendered it in the name of sportsmanship to a bigger whiner after PPIHC changed the race classes, long story). The car has been stored indoors and is ready to prep and race.
Car is located in Brooklyn, WI
This is a race car no title with the car.
You arewelcometo come view the car.
Call or email with Questions 608-395-9684
- Condition: Used
- Make: BMW
- Model: 2002
- Type: Convertible
- Trim: Cabriolet Convertible 2-Door
- Year: 1974
- Mileage: 1,000,000
- VIN: 4228650
- Color: Burgundy
- Engine size: 2.0L 1990CC 121Cu. In. l4 GAS SOHC Naturally Aspirated
- Number of cylinders: 4
- Fuel: Gasoline
- Transmission: Manual
- Drive type: RWD Want to buy? Contact seller!
