1982 Mazda RX-7 Widebody 1.3L Supercharged RX7 FB

Price: US $7,000.00 Item location: Argyle, Texas, United States
  • Condition: Used
  • Make: Mazda
  • Model: RX-7
  • Type: Coupe
  • Trim: GSL Coupe 2-Door
  • Year: 1982
  • Mileage: 9,999,999
  • VIN: JM1FB3315C0602875
  • Color: Blue
  • Engine size: 1.3L Supercharged
  • Number of cylinders: 2
  • Fuel: Gasoline
  • Transmission: Manual
  • Drive type: RWD
  • Interior color: Black
  • Options: Sunroof
  • Vehicle Title: Clear
  • Want to buy? Contact seller!

1982 Mazda RX-7

Up for sale is a well known FB (amongst the FB owners that have been around for a while.) This car was built by Billy Watts the original owner of RE Speed.
The car now has a rebuilt 13B with a Camden Supercharger. The paint could use a little touching up and the front air damn needs a little work.
The car has a Pacifica Widebody Kit on it painted blue and white. The car is street legal with but is best served on the track.

The write up below was written by Billy Watts...

"The shell was completely stripped of all parts. Shell was then prepped by aircraft stripping all the wheel wells, interior and engine compartment. Once clean we began to repair the wheel well rot. Sections were cut out and new sheet welded in place. We used new upper arm support brackets removed from a donor chassis to complete the repair. All non used holes were filled on the firewall with round slugs cut from sheet metal and welded in place. Once the welds were ground down you can not see where the hole were. Threaded bungs were welded in place for the hood pins and the fuel pressure regulator bracket was fabricated and welded to the pinch weld on the firewall. Brackets were fabricated and welded for the second generation oil cooler mounted in front of the radiator. We then covered the tire well with our normal fuel cell block off panel though we have chosen to stay with the stock tank for a while. A simple 4 point bar was fabricated from 1.5" x .095 wall DOM. The bar was built to help support the rear shock area for possible future updates in the back. It was also built so that it can be updated to a full cage later. Once chassis fabrication was completed we sprayed the engine area, interior and wheel wells gloss white.
Our goal with the car is a streetable, track day car that represents our abilities and product line. We wanted to build the vehichle with an "old school" look. It will be used for a few track days her an there as well as to show the vehicle at events like Deals Gap and SevenStock. To attain this goal we decided there would be interior from the main hoop forward. There would be a full street legal wire harness. All the parts for the vehicle would come from our online store or our available sources just as our customers would do."
The following list is what was used and done during the build:


S5 turbo 2 motor with a street port, all new seals, rings, springs, S5 plates with less than 1K miles on them

new S5 rotor housing

new FD oil pump and e-shaft.

FD rotating assemble 9.0 compression
Holley 750 double pump, rebuilt with less than 10 miles on it...

FB gearbox
Mazda Trix New drive shaft with replaceable u-joints
GSL-SE pumpkin
ReSpeed HD Axle retainer plates
PROTOTYPE ReSpeed Pre-Silencer
Borla SS Muffler
ReSpeed fabricated mandrel exhaust. 3" to 2.5" over the axle housing.
ReSpeed Mark I front and rear big brake kit.
Brembo blank rotors, re-drilled 4 lug
ReSpeed re-manufactured caliper sets
ReSpeed Stainless line kit
Rear brake bias lever with stainless plumbing
Front Suspension:
ReSpeed Race coil over kit
ReSpeed 350# front springs
Modified and powder coated front spindles
ReSpeed Caster/Camber Plates
ReSpeed Spherical kits
Tokico 5 way inserts (Race)
ReSpeed 1" Roll center blocks
ReSpeed Tubular Competition Sway Bar
ReSpeed Strut Tower and Firewall Brace
Rear Suspension:
ReSpeed rear spring adjuster kit
ReSpeed 175# springs
ReSpeed Tubular Rear Lower Control Arms
ReSpeed rack/pinion kit with Aluminum engine mount upgrade
Flaming river 15:1 rack
MSD 6A on leading, direct fire
ReSpeed 3 Coil Mount
Autometer Rev Limiter
Two completely independent wiring systems. First one is a painless fuse box kit that handles all ignition, fuel and electric fan circuits. Fuses are mounted to the dash for quick repair. Second is a gutted stock harness that handles the street car aspects like turn signals and wipers. The stock harness was laid out and unwrapped, all unwanted wires were removed. Pop up headlight motors were removed.
ReSpeed FC fuse box bracket.
Relocated battery with fabricated mount structure
ReSpeed Quick headlight pop up stays
Fuel System:
Holly adjustable regulator
ReSpeed 0-10 Fuel Pressure Gauge
ReSpeed Dry Break
Relocated oil filter using ReSpeed block off and filter mount
-10 Stainless oil cooler lines
Second generation oil cooler
ReSpeed Cold air radiator support
15"x8" SportMax wheels - Zero Offest
Tires are 205-50-15

***With the recently rebuilt motor and carburetor...the car need to be tuned before being driven. I also have another 82 FB Widebody for sale that will be posted in another auction.