1964 Ford Fairlane (THUNDERBOLT CLONE PROJECT)

Price: US $12,000.00 Item location: Los Angeles, California, United States
  • Condition: Used
  • Make: Ford
  • Model: Fairlane
  • Year: 1964
  • Mileage: 100,000
  • Fuel: Gasoline
  • Drive type: RWD
  • Vehicle Title: Clear
  • Want to buy? Contact seller!
Description:

1964 Ford Fairlane

IF YOU ARE THINKING ON BUILDING A THUNDERBOLT CLONE OR A GASSER THIS IS YOUR CAR!FINALLY A 1960'S MUSCLE CAR PROJECT THAT HAS THE HARD STUFF DONE.


DONT WAIT THIS WILL BE GONE


FORD FAIRLANE THUNDER BOLT CLONE PROJECT ( MUSCLE CAR CLASS) Note: PROJECT CLONE CAR TheFord Fairlane Thunderboltis a limited production, factory experimental,drag race onlyautomobile built byFordin 1964. A total of 100 units were produced; forty-nine four-speed and fifty-one automatic, enough to secure the 1964NHRASuper Stock title for Ford.

LOTS OF METAL FAB AND CLEAN UP WORK HAS BEEN DONE, THIS THUNDERBOLT PROJECT MIGHT BE THE BEST PROJECT NOW IN PROGRESS, SAVE THOUSANDS AND 100’S OF HOURS OF TIME.

1964 FORD FAIRLANE 2 DOOR POST CAR.

ALREADY FINISHED THUNDERBOLT WORK: MEDIA BLASTED AND PRIMED. LADDER BARS WITH COIL OVERS. SUBFRAME CONNECTORS. MILD STEEL ROLL CAGE. MINI TUBBED. DRIVESHAFT LOOP. BOTH AIR TUBE CLEARANCE PANELS, AIR DUCT HOLES FRONT ON THE SUPPORT, CLEAN FIREWALL, NEW CURRIE 9 INCH HOUSING AND 31 SPLINE AXLES. SHOCK TOWERS CUT FOR BOSS 429 OR SOHC FORD ENGINE OR WOULD ALSO FIT ANY MOD MOTOR OR COYOTE 5. 0 ENGINE.

WHAT COMES WITH :

ORIGINAL WIRE HARNESS. STEERING COLUM.

DRIVERS DOORS WITH DENTS. NICE PASS DOOR.

Shock Tower Export Brace

CRITES FIBERGLASS TEAR DROP HOOD AND TRUNK LID.

MOST ALL INTERIOR TRIM AND DASH PARTS. MOST ALL EXTERIOR TRIM.

REAR BUMPER AND BRACKETS.

GRILL AND FRONT TRIM.

LOTS OF PARTS ALL BAGGED AND TAGGED

SOME THUNDERBOLT CLONE PARTS

ALL GLASS.

CAR DOES HAVE CASTERS ON THE FRONT SO IT ROLLS FINE.

CAR HAS A CLEAR CALIFORNIA DMV TITLE.

CAR IS VERY SOLID

NO UPPER CONTROL ARM MOUNTING POINTS ON CAR.

THIS THUNDERBOLT WAS PLANNING ON THE FATMAN FABRICATION FRONT END SUSPENSION UP GRADE.

PROJECT NOTES: NO FRONT SUSPENSION WITH THIS PROJECT, NO ENGINE, NO TRANSMISSION, NO REAR GEARS, NO SEATS, NO GAGES, NO FUEL TANK,

THE LOWER CONTROL ARM AND ALL STEERING AND STRUT ROD MOUNTING POINTS ARE STILL IN THE FACTORY LOCATIONS.

Any questions please contact us for more photos or videos

No paypal for final payment...CASH or BANK CHECK only

This vehicle is being sold as is, where is with no warranty, expressed written or implied. The seller shall not be responsible for the correct description, authenticity, genuineness, or defects herein, and makes no warranty in connection therewith. No allowance or set aside will be made on account of any incorrectness, imperfection, defect or damage. Any descriptions or representations are for identification purposes only and are not to be construed as a warranty of any type. It is the responsibility of the buyer to have thoroughly inspected the vehicle, and to have satisfied himself or herself as to the condition and value and to bid based upon that judgement solely. The seller shall and will make every reasonable effort to disclose any known defects associated with this vehicle at the buyer's request prior to the close of sale. Seller assumes no responsibility for any repairs regardless of any oral statements about the vehicle.

CALIFORNIA SALES TAX APPLICABLE TO CALIFORNIA RESIDENTS.

This car is for sale locally and we reserve the right to end the auction early. Miles may also change depending on use of the car during the sales period and may be higher than stated.

Buyer is responsible for pickup or shipping of this vehicle.

If you reside out of State or Country the vehicle must be shipped by a commercial carrier or all California taxes will be due upon delivery, by California law. Carrier must be approved by the State of California.