1979 Camaro Z28 572 Swap 760hp! EFI, 4L80, 9" etc , $43k+ invested NO RESERVE!

1979 Chevrolet Camaro Z28

All right everybody, this is the final round, went from 30k to 26k, and now as low as its going to go. I researched ads nationwide and cannot find a comparable combo of properly matched parts with the wanted extras like EFI and modern BUILT electronically controlled transmission with OD ( not to mention a motor with a WARRANTY, not built in "Hack Job Bobs") for a price thats even close. If you are local I encourage you to come take a look. I am on the road a bit but am pretty flexible to show it. I will run this auction one last time if it doesn't go we will just keep it and sell off some other items. Do not message me with offers in the teens, it's not happening! I am giving it away as it is. Yes I know you do not get what you put in, I think half off of NEW stuff is a pretty good deal! And that's just the PARTS.
Up for grabs is my newly completed 1979 Z28 with a 763HP Big Block, Stage 3 (1000hp) 4L80E transmission with Overdrive and transbrake, Strange 9" rear, FiTech EFI

Almost everything on the car is new outside of the body. All components were carefully picked out to handle each other 110% with no corners cut. Keep in mind even if the Camaro itself is not your thing, these parts can transfer into YOUR CLASSIC GM PROJECT with little effort and sell out the rest. The body has NO rust. The complete drivetrain has only 250 miles on it and the motor carries a TWO YEAR UNLIMITED MILEAGE WARRANTY!!

The car runs and drives great as is and is VERY STREETABLE unlike a lot of other "street-strip" cars out there that only have 3 speed transmissions, spools etc

Here is an almost complete list of parts-components installed from front to back. Receipts from parts totals alone are upwards of $33-35k, NOT including any labor OR the cost of the car itself...
B&M Super-plate trans cooler
Dillon 4 core aluminum radiator with two 12" SPAL fans
All new steering components, QA1 tubular upper and lower control arms, coil overs and tie rod ends
C5 Corvette spindle and disc conversion
Manual steering box conversion
Race Star 92 black chrome 17" wheels all the way around..
ALL bushings replaced with Energy Suspension poly, body mounts, engine-trans, suspension etc etc

BBC- Built with Dart Sportsman block, SCAT 4340 forged crank and H beam rods, Wiseco forged pistons, ARP2000 rod bolts, Comp Cams hyd roller cam, tie bar lifters, Heads built with all comp cams hardware, Comp pro magnum rockers, melling oil pump,ARP bolts all around,SFI balancer and flexplate, single plane intake, taylor green wireset, edelbrock black air cleaner... engine was dyno'd and have video to show
CVF Racing 8 rib serpentine setup, aluminum high flow water pump
Powermaster 150 Amp alternator, 1 gauge cables, battery in trunk
Hedman headers- Ceramic coated NO mods needed to fit
MSD black pro billet distributor and coil
FITECH meanstreet 800hp capable EFI system

Manual brake conversion

Jakes Performance Stage 3 4L80 ( 1000hp capable) transmission with OVERDRIVE! and a low gear transbrake
Upgraded to stage 3 level with 300M billet input shaft
Controlled by US Shift quick 4 controller which is FULLY PROGRAMMABLE by your laptop and easy to use program. Set shifts wherever you want, switch to a manual mode etc, way better than self learning
Jakes performance single billet lockup converter, stall speed is around 3200, perfect on the street
G force F body 4L80 crossmember
Action Machine Aluminum driveshaft, rated over 2000 hp, sonnax slip yoke,1350 U Joints
Autometer Gauge package and tach all converted to LED lights, custom aluminum panel
B&M Quicksilver gate/ratchet shifter with transbrake button on handle
Pioneer Bluetooth stereo and front speakers installed in kick panels
Power windows
AC/heat system and vent tubes removed
S&W 8 point roll bar completely welded in and also tied into Heidts subframe connectors, roll bar has extended rear bars to save the back seat
Scat pro car seats and G force camlock 5 point harnesses, rear seats newly covered, new rear interior plastics
Summit (MSD) digital ignition
Tanks INC EFI fuel tank and 1000hp capable in tank pump
All braided feed and return lines
Mickey Thompson ET Street SS Drag Radials basically new 250 mi on them
Pypes Race pro Mufflers and X pipe (also have the over axle pipes- see below)

Strange overbuilt 9" rear setup - powdercoated housing,Daytona pinion setup, Detroit truetrac differential, US gear 3.89 ring and pinion, 35 spline axles with access holes drilled, Wilwood street disc brake setup, Caltrac traction bars, Summit leaf springs, Energy suspension shackles, new spring mount plates
Here's the things the car needs to make it a perfect 10 ( because I know I do not want any surprises when I buy a used car, although it's pretty much new)...

Small ding in driver's door needs a little more smoothing out

The car's black paint is wrapped in removable anthracite gray plasti dip at the moment ( look it up on youtube if you are not familiar with it. cool stuff!), easily peel it off in about 15 mins if you wish and it has a nice black finish. It does have a few clear coat swirls and scratches from dust ( I did post a pic of what it looks like under the wrap for reference). I coated it to protect the current finish.
Back plastic decklid panel needs replaced where speakers mount, I had to cut it to fit roll bars $20
X pipe needs a slight bend to raise the mufflers up, because they are so low I can't install the over axle pipes or they sit too close to the rear end.. I can't find a shop locally that can bend 3"... might be easier to just get rid of the X and do simple 3" true duals.
Fuel gauge only starts going down once it reaches 5 gallons left so it does work but I don't think I calibrated it right when I installed it, float needs adjustment
Linkage is there but no wiper motor or blades installed, wiring plug is also there, just add a motor, I did not as it was to only be driven on nice days
Hood opens and closes fine but could use a more precision alignment and a new, stiffer spring on hood release
Steering wheel needs to be centered, I will most likely fix that this weekend, easy fix
So there you have it, all in all a combo worth upwards of $43k+... Car turns a low 2200 at 70MPH in overdrive, great on the highway and once broken in should run low 10's even 9.90's with a fatter rear slick or pro bracket radial
I need to get cash out of this so I am pricing for a quick sale due to unforeseen upcoming medical expenses ... Again, if you would like this setup in your Chevelle, Nova etc, just swap it all over! This is a bulletproof street/ strip combo that will take anything you can dish out even if you decide to add a power adder etc..The car alone as a rust free roller should still bring a decent chunk of change. I took the time to put it together but have no more free time to take it back apart so with that said...
I AM NOT PARTING IT OUT DON'T ASK
ABSOLUTELY NO FULL OR PARTIAL TRADES, ANY INQUIRY ASKING THAT WILL BE IGNORED!
PREFER CASH OR CERTIFIED FUNDS, WILL NOT GET TITLE UNTIL THEY CLEAR!
NO JOYRIDES
CASH IN HAND DEMOS ONLY
Message me with any questions or for my phone contact info if you would like to chat about itThanks!Steve
**also including the extra ( louder) set of mufflers " Pypes Violators" and the over axle pipes ( not seen in pics), transmission tuning software, all documentation, receipts for parts and sublet labor, manuals on all components and more as I come across things

• Condition: Used
• Make: Chevrolet
• Model: Camaro
• Type: Coupe
• Trim: Z28
• Year: 1979
• Mileage: 250
• VIN: 1Q87L9N515539
• Color: Black
• Engine size: 572 BBC EFI
• Number of cylinders: 8
• Transmission: Automatic
• Drive type: RWD
• Interior color: Black
• Vehicle Title: Clear
Want to buy? Contact seller!